FORMEX FOR GALVANIZED IRON S2003
-
GHS02 - flammable substances 
GHS07 - irritants 
GHS08 - substances hazardous to health 
GHS09 - substances hazardous to the environment
The product is intended to be used as a primer coating of light metals and iron. It is also suitable for coatings of steel under nitrocellulose and synthetic enamels drying out on air. It is endowed with excellent drying and excellent adhesion to many surfaces.
BENEFITS
• active anticorrosive pigment
• excellent adhesion to steel and light metals
• suitable under nitrocellulose and polyurethane enamels
SURFACE PREPARATION
The surface must be clean, dry, degreased, free of rust and dust, mechanically cleaned. Application on galvanized sheet is possible after 12 months of weathering.
First of all the surface must be degreased by means of suitable agent (e.g. BALTECH P6402 technical benzine, BALTECH P6401 acetone or, if it is possible, warm pressurized water with detergent). For removing of residues of various salts it is necessary then to rinse the surface with clear water. Rough and sticky impurities must be removed manually or mechanically (grinding, scraping). Possible rust may be removed also manually or mechanically (metal brushes, grinding discs). Formerly coated surfaces must be cleaned, degreased and without old non-adhesive paints.
Thinner: BALTECH C6000 for spraying, BALTECH S6005 for brush or roller
Spreading capacity: 10 - 12 m2/l per one layer
WORKFLOW
Properly mix before use, thin, if it is necessary. Apply by brush, roller or spraying on prepared surface.
The coating of a metal:
1. 1 coat of S2003 FORMEX FOR GALVANIZED IRON. It dries at temperature of approximately 20 °C. Drying can be accelerated by heating up to 80°C. The coat dried on air can be re-sprayed by synthetic or nitrocellulose enamel already after 1 hour, optimum thickness of one layer is 35 - 40 μm.
2. 1 or 2 coats of synthetic enamel INDUSTROL UNIVERZAL S2013, INDUSTROL UNIMAT S2075 or INDUSTROL PROFI U2129.
SHADES
0110 medium grey, 0600 grey-green, 0840 russet
GHS02 - flammable substances GHS07 - irritants GHS08 - substances hazardous to health GHS09 - substances hazardous to the environment Signal word: Warning
Obsahuje xylen (směs).
| EUH211 | Attention! Hazardous respirable droplets may form when sprayed. Do not inhale aerosols or mist. |
|---|---|
| H226 | Flammable liquid and vapors. |
| H312+H332 | Harmful in contact with skin or by inhalation. |
| H315 | It irritates the skin. |
| H319 | Causes serious eye irritation. |
| H335 | May cause respiratory irritation. |
| H373 | May cause organ damage through prolonged or repeated exposure. |
| H411 | Toxic to aquatic organisms, with long-term effects. |
| P102 | Keep out of reach of children. |
| P210 | Keep away from heat, hot surfaces, sparks, open flames and other sources of ignition. No smoking. |
| P261 | Avoid breathing dust/fume/gas/mist/vapour/aerosols. |
| P273 | Avoid release to the environment. |
| P280 | Wear protective gloves/protective clothing/safety glasses/face shield. |
| P304+P340 | IF INHALED: Move the person to fresh air and keep them in a position that facilitates breathing. |
| P305+P351+P338 | IF IN EYES: Rinse carefully with water for several minutes. Remove contact lenses, if worn and if they can be removed easily. Continue rinsing. |
| P312 | If you feel unwell, call the TOXICOLOGICAL INFORMATION CENTER/doctor/ tel. 224 919 293 or 224 915 402 (24 hours a day) |
| P501 | Remove the contents/packaging according to the instructions on the product. |